[uClinux-dev] error while loading snapgear-3.4.0 image to avila

[Saurav Kumar Barik]

Hi list,

> Hi Saurav,

> Saurav Kumar Barik wrote:
> I downloaded the snapgear-3.4.0 from,
>
>  http://ftp.snapgear.org/pub/snapgear/src/snapgear-3.4.0.tar.gz
>
> I built it refering to the INTEL-IXDP425-HOWTO present at,
>
>  /xxx/yyy/snapgear/Documentation/INTEL-IXDP425-HOWTO
>
> The build was successful with no errors.
>
> But I am facing problem while loading the image onto my Avila board.
>
> The NP on the board is GWIXP425BDT and I am using redboot-v2.02.
>
> Is it the HOWTO I am refering to, is not in compliance with the board I
> am using?
> Also in the HOWTO the image loading part for redboot-v2.02 is not given.

> Can you post all the Redboot messages from its boot?

> Regards
> Greg




> The error message while loading are given below.
>
> Please note that I also tried using "exec" instead of "go 0x01600000" as
> given in the HOWTO, but with no luck.
> I googled a lot and could not find any concrete solution.
> I am still stuck at the same problem.
>
> If anybody out there has any clues, please help....
>
> Thanks & Regards,
> Saurav
>
>
> ERROR MESSAGE
>
> RedBoot>
> RedBoot>
> RedBoot>
> RedBoot> ip_address -l 192.168.157.206 -h 192.168.157.52
> IP: 192.168.157.206/255.255.255.0, Gateway: 192.168.1.1
> Default server: 192.168.157.52
> RedBoot>
> RedBoot>
> RedBoot> load -r -v -b 0x01600000 zImage
> Using default protocol (TFTP)
> |
> Raw file loaded 0x01600000-0x01703a07, assumed entry at 0x01600000
> RedBoot>
> RedBoot> load -r -v -b 0x00800000 ramdisk.gz
> Using default protocol (TFTP)
> \
> Raw file loaded 0x00800000-0x008d76ba, assumed entry at 0x00800000
> RedBoot>
> RedBoot>
> RedBoot> go -n 0x01600000
> $T0a0f:01600028;0d:07fc0fec;#18$T0a0f:01600028;0d:07fc0fec;#18$T0a0f:01600028;0d
> :07fc0fec;#18$T0a0f:01600028;0d:07fc0fec;#18$T0a0f:01600028;0d:07fc0fec;#18$T0a0
> f:01600028;0d:07fc0fec;#18$T0a0f:01600028;0d:07fc0fec;#18$T0a0f:01600028;0d:07fc
> 0fec;#18

Thanks a lot for your help and replies.
I am sorry, as there was an endian issue in the image built & the target board.
I got the images built again and loaded properly.


Thanks again,
Saurav



The information contained in, or attached to, this e-mail, contains confidential information and is intended solely for the use of the individual or entity to whom they are addressed and is subject to legal privilege. If you have received this e-mail in error you should notify the sender immediately by reply e-mail, delete the message from your system and notify your system manager. Please do not copy it for any purpose, or disclose its contents to any other person. The views or opinions presented in this e-mail are solely those of the author and do not necessarily represent those of the company. The recipient should check this e-mail and any attachments for the presence of viruses. The company accepts no liability for any damage caused, directly or indirectly, by any virus transmitted in this email.

www.aztecsoft.com
-------------- next part --------------
An HTML attachment was scrubbed...
URL: http://mailman.uclinux.org/pipermail/uclinux-dev/attachments/20070129/a75b77a9/attachment.html